根據《建筑工程施工質量驗收統一標準》GB 50300-2013的要求，檢驗批質量驗收記錄要填寫檢驗批容量。

　　According to the requirements of the Unified Standard for Construction Quality Acceptance of Building Engineering GB 50300-2013, the inspection batch capacity should be filled in the inspection batch quality acceptance record.

　　對檢驗批來說，檢驗批容量就是檢驗批中主要驗收項目的工程量。對具體驗收項目來說，檢驗批容量是按質量驗收規范規定的計量單位計算的驗收實體的數量。一個檢驗批，驗收實體對象可能有多種，檢驗批容量要分別計算

　　For inspection batches, the inspection batch capacity refers to the engineering quantity of the main acceptance items in the inspection batch. For specific acceptance projects, the inspection batch capacity is the quantity of acceptance entities calculated according to the measurement units specified in the quality acceptance specifications. A single inspection batch may have multiple physical objects for acceptance, and the capacity of each inspection batch needs to be calculated separately

　　1、比如模板安裝檢驗批，如果把柱、梁、板模板安裝劃為一個檢驗批，這個檢驗批就包括柱模板、梁模板、板模板3種驗收實體對象。

　　1. For example, for template installation inspection batches, if the installation of column, beam, and slab templates is divided into one inspection batch, this inspection batch includes three types of acceptance entities: column templates, beam templates, and slab templates.

　　2、按規范要求，“在同一檢驗批內，柱模板應抽查構件數量的10%，且不少于3件”，柱模板的計量單位就是構件，檢驗批容量就是本檢驗批含多少件柱(多少根柱)。對梁模板來說，“梁模板應抽查構件數量的10%，且不少于3件”，梁模板的計量單位也是構件，檢驗批容量就是本檢驗批含多少件梁(多少道梁)。對板模板來說，“板模板應按有代表性的自然間抽查10%，且不少于3間”，板模板的計量單位就是自然間，檢驗批容量就是本檢驗批含多少間板(多少塊板)。

　　2. According to the standard requirements, "within the same inspection batch, 10% of the number of components should be randomly inspected for column templates, and not less than 3 pieces should be inspected." The unit of measurement for column templates is the components, and the inspection batch capacity is the number of columns (or columns) included in this inspection batch. For beam formwork, "10% of the number of components should be randomly inspected, and not less than 3 pieces". The unit of measurement for beam formwork is also the components, and the inspection batch capacity is the number of beams (how many track beams) included in this inspection batch. For board templates, '10% of representative natural rooms should be randomly sampled, and not less than 3 rooms should be selected'. The unit of measurement for board templates is natural rooms, and the inspection batch capacity is the number of rooms (or pieces) contained in this inspection batch.

　　3、比如土方開挖檢驗批，包含基底和邊坡兩種驗收實體對象。規范要求“場地表面每100~400m2取一點，但不應少于10點”，基底的計量單位就是“m2”，基底的檢驗批容量就是基底面積。對邊坡，“每20m取1點，每邊不應少于1點”，邊坡的計量單位就是“m”，邊坡的檢驗批容量就是邊坡長度。

　　3. For example, the earthwork excavation inspection batch includes two types of acceptance entities: the foundation and the slope. The standard requirement is to take one point every 100-400m2 on the surface of the site, but not less than 10 points. The measurement unit of the substrate is "m2", and the inspection batch capacity of the substrate is the substrate area. For slopes, 'take 1 point every 20m, and each side should not be less than 1 point', the unit of measurement for slopes is'm ', and the inspection batch capacity for slopes is the length of the slope.

　　4、檢驗批質量驗收記錄中，檢驗批容量的填寫，可以分為以下幾種形式:

　　4. In the quality acceptance record of inspection batches, the filling of inspection batch capacity can be divided into the following forms:

　　4.1.檢驗批容量為當前施工段的主要工程量，具體表現是，混凝土澆筑時檢驗批容量為“口”，鋼筋安裝時檢驗批容量為“t”4.2.檢驗批容量為當前施工段的施工范圍，可以理解為當前施工段的水平投影面積，具體表現是模板安裝時檢驗批為“m2“4.3.檢驗批容量為當前施工的構件數量，具體表現是，混凝土澆筑框架柱時檢驗批容量為“根”，門塑窗安裝時檢驗批容量為“樘”。

　　4.1. The inspection batch capacity is the main quantity of the current construction section, specifically manifested as the inspection batch capacity of "mouth" during concrete pouring and "t" during steel bar installation. 4.2. The inspection batch capacity is the construction scope of the current construction section, which can be understood as the horizontal projection area of the current construction section, specifically manifested as the inspection batch of "m2" during template installation. 4.3. The inspection batch capacity is the number of components in the current construction, specifically manifested as the inspection batch capacity of "root" during concrete pouring of frame columns and "frame" during door and plastic window installation.

　　本文由 山東電纜橋架  友情奉獻.更多有關的知識請點擊  http://m.12xw.com/  真誠的態度.為您提供為的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Shandong Cable Bridge For more related knowledge, please click http://m.12xw.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.